# Anyone using center drills?

**URL:** <https://forum.avidcnc.com/t/anyone-using-center-drills/2446>\
**Category:** General Chat\
**Created:** [September 13, 2023, 12:16pm UTC](https://forum.avidcnc.com/t/anyone-using-center-drills/2446 "2023-09-13T12:16:47Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![ROTM](https://avatars.discourse-cdn.com/v4/letter/r/90ced4/32.png) [@ROTM](https://forum.avidcnc.com/u/ROTM)\
**Post date:** [September 13, 2023, 12:16pm UTC](https://forum.avidcnc.com/t/anyone-using-center-drills/2446/1 "2023-09-13T12:16:47Z")

</div>

Good day.  
I am looking to mark the center/starter holes in Alum and steel.  
Anyone else doing this? which center drill or other methods are you guys using?

Thank you!

---

<div class="post-metadata">

**Author:** ![da-kengineer-meister](https://avatars.discourse-cdn.com/v4/letter/d/f1d935/32.png) [@da-kengineer-meister](https://forum.avidcnc.com/u/da-kengineer-meister)\
**Post date:** [September 13, 2023, 6:09pm UTC](https://forum.avidcnc.com/t/anyone-using-center-drills/2446/2 "2023-09-13T18:09:57Z")

</div>

It wasn’t clear from the terminology used to ask the question exactly what you are looking for? The wording ‘mark’ threw me a bit there. Assuming here you are asking about how to start a hole without plunging?

Quite a few of us here use helical entry to clear chips while starting a hole. Most modern CAD systems support helical entry which can be quite helpful, but possibly there is a missinterpretation of the question here?

---

<div class="post-metadata">

**Author:** ![ROTM](https://avatars.discourse-cdn.com/v4/letter/r/90ced4/32.png) [@ROTM](https://forum.avidcnc.com/u/ROTM)\
**Post date:** [September 13, 2023, 7:26pm UTC](https://forum.avidcnc.com/t/anyone-using-center-drills/2446/3 "2023-09-13T19:26:12Z")

</div>

Maybe I should have said a small pilot hole. for instance in alum for the machine to drill a small 2.5 mm hole at 2 or 3mm depth. Tnx.

---

<div class="post-metadata">

**Author:** ![da-kengineer-meister](https://avatars.discourse-cdn.com/v4/letter/d/f1d935/32.png) [@da-kengineer-meister](https://forum.avidcnc.com/u/da-kengineer-meister)\
**Post date:** [September 13, 2023, 8:50pm UTC](https://forum.avidcnc.com/t/anyone-using-center-drills/2446/4 "2023-09-13T20:50:49Z")

</div>

Would a 120or 135deg carbide NC-Spotting drill suffice to create the initial divot and ensure that the follow on twist drill does not wander?

---

<div class="post-metadata">

**Author:** ![subnoize](https://yyz1.discourse-cdn.com/flex027/user_avatar/forum.avidcnc.com/subnoize/32/2197_2.png) [@subnoize](https://forum.avidcnc.com/u/subnoize)\
**Post date:** [September 13, 2023, 11:59pm UTC](https://forum.avidcnc.com/t/anyone-using-center-drills/2446/5 "2023-09-13T23:59:22Z")

</div>

I use 1/2 size of the final hole end mill. I use flat or square noses end mills so I don’t ruin my flow through table top.

The main thing I cut are holes for rivets in aluminum sheet for aircraft. Usually custom ribs and skins as a builder assistance type service.

I never use drills because they have a point and they tear up the flow through table top and then nothing will stick to it.

Which is why I rant and rave about people cutting gashes in their spoilboards. Drives me nuts. My spoilboards go bad because of expansion from moisture, almost never because of end mill gashing.

PS. I do take the holes larger with a second tool but the starter hole is most what folks want because of cost.
